How To Fix Keurig k Duo When Its Not Pumping Water

If you’re experiencing issues with your Keurig K Duo not pumping water, I understand how frustrating it can be to not get your morning coffee fix. But don’t worry, there are a few things you can try to fix the problem and get your Keurig up and running again.

How To Fix Keurig k Duo When It’s not Pumping Water

One of the most common reasons for a Keurig K Duo not pumping water is that the water reservoir may not be properly seated on the machine. Make sure it is firmly in place. Another possible reason is that there may be an air bubble in the water line.

To fix this, try running a few cycles of just water through the machine without a K-Cup. You can also try cleaning the machine’s needle, which may be clogged with coffee grounds or other debris.

If none of these solutions works, there may be a more serious issue with your Keurig K Duo. In that case, it’s best to contact Keurig customer support for further assistance.

Remember, regular maintenance of your Keurig K Duo can help prevent issues like this from occurring. Keurig recommends descaling your machine every three to six months, depending on how often you use it and the hardness of your water. And don’t forget to clean the machine’s needle regularly to prevent clogs.

In this article, we will provide you with a step-by-step guide on how to fix your Keurig K Duo when it’s not pumping water.

How To Fix Keurig k Duo When It’s Not Pumping Water? Step By Step Guide:

Step 1: Check the Power Source

The first thing you should do is check the power source of your Keurig K Duo. Make sure it’s plugged in and the outlet is working correctly. If the outlet is faulty, you may need to try a different one. Also, make sure that the power cord is securely plugged into the back of the machine.

Step 2: Clean the Machine

If the power source is not the issue, the next step is to clean the machine. Over time, the Keurig K Duo can accumulate mineral deposits, which can clog the system and prevent it from pumping water. Here’s how you can clean the machine:

1. Turn off the machine and unplug it from the power source.
2. Empty the water reservoir and remove the pod holder.
3. Use a damp cloth to clean the exterior of the machine.
4. Fill the water reservoir halfway with white vinegar and the rest with water.
5. Place a cup or mug on the drip tray, and then run a brew cycle without a pod.
6. Discard the contents of the cup, and then repeat the process until the water reservoir is empty.
7. Rinse the water reservoir with clean water, and then fill it with fresh water.
8. Run a few brew cycles without a pod to rinse the machine thoroughly.
9. Finally, replace the pod holder and fill the water reservoir with fresh water.

Step 3: Check the Water Reservoir

If cleaning the machine doesn’t solve the problem, the next step is to check the water reservoir. Make sure it’s filled to the maximum level, and there are no blockages in the water line. If the water reservoir is not correctly positioned, the machine may not pump water. To fix this issue, remove the water reservoir and reattach it, making sure it’s in the correct position.

Step 4: Check the Pump

If the machine is still not pumping water, the next step is to check the pump. The pump is responsible for pushing water through the machine, and if it’s not working correctly, the machine will not pump water. Here’s how you can check the pump:

1. Turn off the machine and unplug it from the power source.
2. Remove the water reservoir and the pod holder.
3. Use a screwdriver to remove the bottom panel of the machine.
4. Locate the pump, which is a small, black box with wires attached to it.
5. Check the wires for any signs of damage or wear and tear.
6. Use a multimeter to check the voltage of the wires. If the voltage is zero, the pump is faulty, and you need to replace it.
7. If the voltage is not zero, then the pump is working correctly, and the issue may be with the circuit board.

Step 5: Check the Circuit Board

If the pump is working correctly, the next step is to check the circuit board. The circuit board controls the pump and other functions of the machine, and if it’s faulty, the machine will not pump water. Here’s how you can check the circuit board:

1. Turn off the machine and unplug it from the power source.
2. Remove the water reservoir and the pod holder.
3. Use a screwdriver to remove the bottom panel of the machine.
4. Locate the circuit board, which is a small, green board with various components attached to it.
5. Check the board for any signs of damage, such as burnt or corroded components.
6. Use a multimeter to check the voltage of the board. If there is no voltage or the voltage is incorrect, the board is faulty, and you need to replace it.

Step 6: Replace Faulty Components

If you’ve identified a faulty component, such as the pump or circuit board, the next step is to replace it. You can order replacement parts online or purchase them from a Keurig service center.

To replace a faulty pump, follow these steps:

1. Turn off the machine and unplug it from the power source.
2. Remove the water reservoir and the pod holder.
3. Use a screwdriver to remove the bottom panel of the machine.
4. Locate the faulty pump and disconnect the wires.
5. Remove the pump from the machine.
6. Install the new pump and reconnect the wires.
7. Replace the bottom panel and reattach the water reservoir and pod holder.

To replace a faulty circuit board, follow these steps:

1. Turn off the machine and unplug it from the power source.
2. Remove the water reservoir and the pod holder.
3. Use a screwdriver to remove the bottom panel of the machine.
4. Locate the faulty circuit board and disconnect the wires.
5. Remove the circuit board from the machine.
6. Install the new circuit board and reconnect the wires.
7. Replace the bottom panel and reattach the water reservoir and pod holder.

Step 7: Contact Keurig Customer Support

If you’ve tried all the above steps and the machine is still not pumping water, it’s time to contact Keurig customer support. They can provide you with further guidance or arrange for a repair or replacement of the machine if it’s still under warranty.

FAQs

Why is my Keurig K Duo not pumping water?

There could be a few reasons for this. One common issue is that the water reservoir may not be properly seated on the machine. Make sure it is firmly in place. Another possible reason is that there may be an air bubble in the water line. To fix this, try running a few cycles of just water through the machine without a K-Cup. You can also try cleaning the machine's needle, which may be clogged with coffee grounds or other debris.

How do I clean the Keurig K Duo?

To clean your Keurig K Duo, first unplug the machine and let it cool down. Then, remove the water reservoir and empty any remaining water. Clean the reservoir with warm, soapy water and rinse thoroughly. Next, use a paperclip or a cleaning tool specifically designed for Keurig machines to clean out the needle that punctures the K-Cup. Run several cycles of just water through the machine to flush out any remaining debris.

How often should I descale my Keurig K Duo?

Keurig recommends descaling your machine every three to six months, depending on how often you use it and the hardness of your water. If you notice a decrease in the performance of your machine, such as slower brewing times or a weaker coffee flavor, it may be time to descale your machine. You can also check the user manual for specific descaling instructions.

Conclusion:

A Keurig K Duo not pumping water can be a frustrating issue, but there are several steps you can take to troubleshoot and fix the problem. The first step is to check the power source and clean the machine.

If that doesn’t work, check the water reservoir, pump, and circuit board for faults. If you’ve identified a faulty component, you can replace it.

However, If none of these steps works, contact Keurig customer support for further guidance. By following these steps, you can get your Keurig K Duo pumping water again and enjoy your favorite beverages.